Otkon.com.tr
STEPPING
MO
T
O
RS
5 Phase with A
5-Phase with DC Driver
Stepping
Controller
2 Phase with DC Driver
SG8030JY ························································B-244
Stepping
Accessories
ORIENTAL MOTOR GENERAL CATALOGUE
STEPPING
Compact and Simple Controllers
MO
SG8030JY
T
O
RS
The SG8030JY is a compact controller that
switches between two control methods
according to the application: sequential
positioning and data selection positioning.
With sequential positioning mode, you execute
up to four positioning control operations in the
pre-determined sequence by just inputting the
5-Phase with A
start command from the programmable
controller. In data selection positioning mode,
positioning is controlled by selecting one of four
sets of pre-registered positioning data and
Now the Panel-Mount Model isavailable.Allow conventional delay for
inputting the start command from the
shipping. See your agency for detail.
programmable controller.
SG8030JY-D
SG8030JY-U
5-Phase with DC Driver
Ⅵ
Main Specifications
High-Performance Packed in
Set data with touch keys on front panel (record in
48mmϫ
48mm Compact Units
Ⅲ With dimensions of 48mmϫ48mmϫ83.8mm, these
units are the smallest of Oriental Motors controllers.
They come in Flush Mounting and Recessed Mounting
Starting pulse speed 100-10000 HzAcceleration rate 1-100 ms/kHz
For the acceleration/deceleration
pattern, you may select the linear or
Stepping
S-shaped pattern.
Ⅲ In addition to the linear acceleration/deceleration
acceleration/deceleration along an S-shaped pattern.
Sensor detection of home throgh designation of
2-Phase with DC Driver
When you select this S-shaped pattern, the motor can
mechanical home detection direction of rotation.
DC 24 V photocoupler input, input resistance 4.7 k Ω
current sinking inputPNP transistor output linked to photocoupler, 24V
The control methods can be switched.
DC, 25mA or less, current sourcing output
Ⅲ You can also switch the control between sequential
positioning and data selection positioning.
Stepping
Functions
Ⅲ These stepping motor controllers, they have all the most
commonly used functions.
ⅷControl modes: External, Program, Test
ⅷOperating modes: Positioning, Return to mechanical
Example of Basic System Configuration
Accessories
SG8030JY
ORIENTAL MOTOR GENERAL CATALOGUE
STEPPING
Ⅵ
Operating methods
MO
Sequential Positioning Type
Data Selection Positioning Type
T
O
RS
ositioning
P
Sequential positioning type performs positioning in order from the
Data selection positioning type performs positioning in order after
first data every time a START signal is input.
positioning data 1-4 are selected and a START signal is input.
5 Phase with A
External input mode
When a START signal is input, it moves towards the preset sensor at the operating pulse speed (VR), to return to the origin.
Return to mec
5-Phase with DC Driver
It continuously operates as long as a CW or CCW scan signal is
When operating at the continuous operation mode, it keeps the
input, no matter what operating mode is set (It reduces the speed
operation as long as a CW or CCW scan signal is input (It reduces
and stops when a OFF signal is input).
the speed and stops when a OFF signal is input).
operation
The next four operation can be confirmed manually by using the
Data selection positioning operationContinuous operation
Confirmation of
Stepping
operation man
Ⅵ
Wiring diagram
Ⅵ
Signal table
2 Phase with DC Driver
Signal names and functions of Sequential positioning type andData selection positioning type differ in Pin No. 1, 10, 11 only.
q When in the Sequential positioning type
w When in the Data selection positioning type
Stepping
SG8030JY
q : Switching positioning and home detection
w : Switching positioning and home detection
Input Start signal for Positioning and Home detection operation
Accessories
7 Pulse <CW pulse> Output Pulse <CW-pulse output terminal>
Output Direction <CCW-pulse output terminal>
✽1 The pulse output section uses a constant-current circuit, so no external
Input Stop all operation Stop busy output
If another power supply is used for the pulse output section, for example +5V
power, connect the 24V DC and another power supply GND terminals each other.
✽3 This should be conductive (B contact) during normal operation.
When not using the emergency stop input signal, always connect to the
The "E.StoP" message is displayed when the power supply goes off.
✽4 The names in angle brackets < > signals are for data selection
The operating modes given in square brackets [ ] are activated when operationmode select input is on. The names in angle brackets < > signals are for 2-pulse output.
ORIENTAL MOTOR GENERAL CATALOGUE
STEPPING
MO
T
O
RS
Ⅵ
Dimensions Scale 1/4, Unit=mm
Mass: 0.1kg (Without accessories)
5-Phase with A
ⅷ
SG8030JY-D
ⅷ
SG8030JY-U
5-Phase with DC Driver
Stepping
2-Phase with DC Driver
Stepping
Accessories
ORIENTAL MOTOR GENERAL CATALOGUE
Source: http://www.otkon.com.tr/dosya/SG8030%20Serisi%20Katalog%20(0,2%20Mb).pdf
HYPERION Lithium Balance Adapter - For Lithium Polymer and A123 Warnings: Batteries can be a fire hazard if charged or discharged improperly. Always use your battery charger and batteries as directed by the makers. Never Charge Batteries unattended Charge in an area free of flammable materials, on non-flammable brick, concrete, etc Keep Batteries, Charger, and Balancer AWAY FROM
DONATED DENTAL SERVICES (DDS) Dear Applicant: In response to your request for more information regarding how to apply for donated dental care, we are pleased to provide the following information and application for the Donated Dental Services Program (DDS), a program of Dental Lifeline Network·Montana. ELIGIBILITY : Dentists in Montana have volunteered to provide comprehensive